Merging Pyramix Installation Guide Page 6

  • Download
  • Add to my manuals
  • Print
  • Page
    / 35
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 5
Merging Technologies
Le Verney 4, CH-1070 Puidoux Switzerland
www.merging.com/Pyramix T : +41 21 946 04 44 F : +41 21 946 04 45
The Virtual Tracks were removed from Pyramix 7.0. It is no longer possible for users to create
them. Note that they are still supported when coming from older projects. As a replacement we
recommend the use of the Automation Sub-Tracks from now on.
Libraries: Search Results created with the 7.0SP1 version have been corrupted due to an internal
bug. You need to purge all search results created with version SP1 either by completely deleting
the Search_Results_.pml file OR by deleting the corresponding folders in the search result view
Changing project sampling rate 1FS/DSD/DXD within the same Pyramix session can at times
cause problems (Mixer stuck at wrong sampling rate). Workaround: launch back Pyramix.
Final Check Metering: When running MassCore on more than one core, it is possible (though not
always the case) that Final Check cannot monitor certain bus/stem (No metering, but it works
again when selecting another bus)
Workaround 1: Do not use final check with more than one core.
Workaround 2: Add an effect (any effect will do, but you may prefer to pick one that
doesn’t modify the sound: phase oscillo, surround monitor…) on the bus that final
check doesn’t want to monitor.
Low Memory Condition Warning:
A warning informs users when the system is reaching Low Memory Conditions. In order to
save a project under such conditions Pyramix will switch to Save to Disk mode as not enough
memory might be available otherwise. This warning was added in order to prevent a Runtime
Error on Save.
Note that the Save time in Save to Disk mode in Low Memory Condition might take a longer
time since the memory is being dumped to disk in order to allow the users to save their
projects. We recommend afterwards to exit and restart Pyramix in order to free all memory.
This Low Memory warning threshold can be adjusted by the user if one wishes it to come
earlier or later. With every systems and workflows being different, Merging leave you the
ability to adjust when the Warning will show up.
Procedure:
Close Pyramix
Type regedt32 in the run command
In the registry go to HKEY_CURRENT_USER\Software\Merging
Technologies\Pyramix\Settings\Save to disk threshold (this key will only appear if at
least one save was made using that version)
Default value in Decimal mode has been set to 15
- The higher the value is set, the earlier the Low Memory warning will come
- The lower the value is set, the riskier it is for you to encounter a Runtime Error at
save (previous Pyramix versions value would have had this value set to 0)
Merging with this Pyramix v7.0 version has significantly reduced the memory consumption of
Pyramix when confronted with the task of loading enormous libraries. For the long term, the
move of our applications to a 64 bit operating system will provide a very solid platform to
accommodate the ever growing project size requirements of some of our users.
MT-USBSync install problems: Use the latest driver in Merging’s Support Download section.
Cannot use DiscWrite with Pyramix:
Workaround: Re-install Pyramix (maybe run clean up after un-installing Pyramix) or Re-install the
Gear driver. Prior to re-installing such drivers use the Gear Removal Utility below.
Gear Removal Utility:
http://www.gearsoftware.com/downloads.php?dir=updates/windows/drivers/&file=Driver_Remover.exe
Find other Gear links that may be useful to determine if the drivers are installed and functioning
correctly and other tips: Gear Driver Status:
http://www.gearsoftware.com/wiki/index.php?title=Determining_if_GEARAspi_drivers_are_installed_correctly
Gear Known Issues:
http://www.gearsoftware.com/rss/GEAR-drivers-feed.php
Page view 5
1 2 3 4 5 6 7 8 9 10 11 ... 34 35

Comments to this Manuals

No comments